Call (980) 478-8030

Commercial Equipment Troubleshooting Guides

Symptom → the causes a technician checks first. Safe first steps for staff are on each equipment page; anything electrical, gas or refrigerant should be handled by a qualified technician.

Ice machine

SymptomCommon causes
Not making ice / low productionDirty condenser coil or failed condenser fan; hot ambient (>90°F) or poor clearance; low/no water supply, clogged filter; scale on evaporator; failed water pump; refrigerant leak / weak compressor; bin control stuck 'full'.
Long freeze cycle (E01 / 3 beeps / Error 1)Condenser airflow, water inlet valve leaking into sump, hot gas valve leaking by, TXV, low charge, float switch, dirty evaporator.
Ice won't release / long harvestScale on evaporator (clean & descale), hot gas valve not opening, harvest assist, curtain switch, machine not level, thermistor.
Small, cloudy, hollow or incomplete cubesLow water flow, clogged distribution tube, dirty machine, wrong ice thickness probe setting, machine not level, low water pressure.
Water leakingClogged/obstructed drain, cracked water trough, bad float, distribution tube off, bin drain blocked.
Machine runs but bin overflowsBin control/thermostat or bin level probe failed, curtain switch stuck.
Slime / mold / odorMissed cleaning schedule; run clean + sanitize, replace filter, check air quality (yeast near bakeries/bars).

Reach-in refrigerator / freezer

SymptomCommon causes
Running but not coolingDirty condenser coil (most common), condenser fan failed, iced evaporator (defrost failure), evaporator fan failed, low charge/leak, failed start relay/compressor.
Too warm / high temp alarm (HA, A01, Er 7, tHi)Door left open or not closing, torn gasket, overloaded with warm product, blocked air vents, dirty condenser, defrost problem.
Freezing product (cooler)Thermostat/setpoint too low, failed probe, insufficient clearance, controller fault.
Iced-up evaporatorDefrost heater, defrost termination sensor (P2/E2), defrost timer/controller, door gasket letting in humid air.
Water on floor / insideClogged drain tube, frozen drain line (freezer, failed drain heater), condensate pan heater/float.
Runs constantly / short cyclingDirty condenser, gasket leaks, low charge, bad probe, oversized load, ambient too hot.
Compressor won't start / clickingStart relay/capacitor, overload, low voltage, failed compressor.
Probe error (P1/P2/E1/E2/E29)Ohm the NTC probe vs. chart, inspect connector/wiring for water intrusion, replace probe, then controller.

Prep table

SymptomCommon causes
Top rail (pans) warm, cabinet OKLid left open, pans overfilled above line, dirty condenser, top-rail fan/air duct blocked, ambient heat from cook line.
Cabinet warmSame as reach-in: condenser, gasket, evaporator fan, defrost.
Ice on cold wall / railDefrost failure, door gasket, humid kitchen air.
Water leaking under tableClogged drain, evaporator pan, cracked drain tube.
Lid / hinge / cutting board issuesWorn hinge, warped lid gasket, damaged board brackets.

Walk-in cooler / freezer

SymptomCommon causes
Box temperature too high (A1)Door not closing / heater strip, damaged gasket or sweep, evaporator iced, condenser dirty, low charge, failed compressor, failed EC fan motor.
Evaporator coil frozen solidDefrost heater or termination failure, fan delay, defrost timer/controller settings, door ajar, low airflow.
Ice on floor / ceiling / door frameDoor heater wire failed, gasket gaps, panel seal, pressure relief vent.
System won't start (A3, E7)High/low pressure switch open, oil pressure, low voltage, contactor, compressor.
Short cycling / pump-down issuesLiquid line solenoid leaking, low charge, LP switch setting, TXV.
Water leaking from evaporatorDrain line frozen (drain heater), clogged drain pan, pan not pitched.

Cooler (bar / bottle / merchandiser)

SymptomCommon causes
Not cold enoughDirty condenser (lint/grease behind bar), blocked airflow, evaporator fan, overloading with warm product, door gasket.
Condensation on glass doorsDoor heater/anti-sweat circuit, high humidity, gasket.
Lights out / ballastLED driver or ballast, door switch.
NoisyFan blade hitting ice, loose panels, failing fan motor, unit not level.

Commercial washer

SymptomCommon causes
Won't start / door won't lockDoor lock or switch, door not closed, coin/payment system fault, control board, emergency stop open.
Won't fill / slow fillWater supply valves, inlet screens, inlet valve, pressure switch/air dome tube, low water pressure.
Won't drainDrain valve stuck/clogged, lint/debris, pump (if equipped), pressure switch tube, standpipe height.
Won't spin / spins slowlyDrive/inverter fault, motor, belt, out-of-balance load, bearings, braking resistor.
Excess vibration / walkingUnbalanced load, leveling, worn shocks/springs, mounting bolts (hard-mount extractors), bearings.
LeakingDoor boot/gasket, hoses, drain valve, tub seal/bearing (rust trail), dispenser.
Drive / inverter errorsOvercurrent, overvoltage, overheating — check motor turns freely, wiring, ground, cooling fan, line voltage.

Commercial dryer

SymptomCommon causes
No heatGas: igniter, flame sensor, gas valve coils, gas supply. Electric: element, contactor. Both: high-limit, thermistor, airflow switch, sail switch.
Long dry timesLint screen and lint chamber, exhaust duct restricted or too long, blower wheel clogged, low gas pressure, overloading.
Overheating / high-limit tripsRestricted exhaust, failed blower, thermistor, cycling thermostat.
Drum won't turnBelt, idler, drive motor, centrifugal switch, door switch.
Noisy / squealDrum rollers/bearings, idler pulley, belt, blower wheel loose.
Sensor errors (OP/SH)Open or shorted thermistor — test and replace.

Commercial dishwasher

SymptomCommon causes
Dishes not clean / food residueClogged wash arms or nozzles, dirty strainers/scrap screens, low wash temperature, detergent pump not dosing, wrong water level, worn wash pump impeller.
Low rinse temperature / won't sanitize (LOW RINSE TEMP)Booster heater element or thermostat, high limit tripped, low incoming water temperature, scale on element, chemical sanitizer pump empty (low-temp machines).
Won't fill / fill errorWater supply valve closed, clogged inlet strainer, fill solenoid, float or level probe dirty, low water pressure.
Won't drain / drain errorFood debris in drain, drain pump or drain valve failed, clogged drain hose, pressure switch tube blocked.
Leaking from doorDoor gasket worn, overfilling (level probes dirty), machine not level, wash arm end caps missing.
Spots / white film on dishesHard water scale — delime the machine, check water softener, rinse-aid pump.
Conveyor jam (rack conveyors)Rack caught, pawl bar or drive motor, broken curtains, overload.

Commercial oven / combi oven

SymptomCommon causes
Not heatingGas: igniter, flame sensor, gas valve, ignition module, gas pressure. Electric: element, contactor, high limit tripped. Both: temperature probe, control board.
Uneven cooking / hot spotsConvection fan motor slow or failed, fan blade loose, door gasket leaking, wrong rack loading, failed element bank.
Temperature off from setpointProbe out of calibration, thermostat calibration, door seal, control board.
Convection fan won't runDoor switch, fan motor, motor capacitor, inverter (variable-speed models), relay.
Combi: no steam / low humidityScale in steam generator, water supply, solenoid, level electrode, water too pure (RO) or too hard.
Combi: CleanJet / cleaning faultsLow water pressure, clogged nozzle, care pump, drain valve.
Rapid-cook: F2 low cook tempClogged air nozzles/catalyst, door seal, heater, blower, low voltage.
Door won't close / glass condensationHinge, latch, door gasket, door adjustment.

Commercial fryer

SymptomCommon causes
Won't heatGas: pilot out, thermocouple, gas valve, igniter, ignition module. Electric: element, contactor. Both: high limit tripped, drain valve open (interlock), probe.
Oil overheating / high limit trips (E-5, HOT, Hi)Probe out of calibration, thermostat stuck, gas valve stuck open, contactor welded.
Slow recovery (E25/E26)Weak burner or element, low gas pressure, dirty burner/flue, failing probe.
Pilot won't stay litThermocouple or thermopile, dirty pilot orifice, draft, gas valve.
Filtration problems (E09, pump won't fill)Dirty filter pad, pump motor tripped, filter pan not seated, clogged lines, return/drain valve actuators.
Oil leakingDrain valve seal, cracked frypot, high-limit or probe fittings, filter lines.
Pressure fryer won't build pressureLid gasket, deadweight valve, solenoid, lid not latched.

Equipment down right now?

Same-day commercial service across the Charlotte area · Open 7 days · 7:00 AM – 10:00 PM

📞 Call now